34169 LIFTER MAGNET
● Suitable for carrying various Iron material work-piece.
● Very easy operation with the sepcial design of ON/OFF switch.
● Workpiece surface will not be damaged during working.
● High holding magnetic power, this lifter can be used seccessive. Electro power is no necessary for the lifter to avoid power failure problem.
※ Safety Precautions
1. Before lifting workpiece, please check if any material or iron chip exists between the lifter and work-piece, please clean up the surface of the lifter and work-piece.
2. Check switch position to make sure it set correctly, also check the help workpiece being help completed and balanced before lifting.
3. Please do not switch the handle "on" if it is not being used to avoid any damage caused.
4. Please do not use the product if the working piece surface tepmperature is higher than 80℃ degree.
※ Lifting heavy loads due to the following factors to change its load capacity
1. The thickness of steel
2. The roughness of the plane
3. Material quality
4. Lifting magnetic chuck and steel contact surface is clean and smooth
單位：mm
| Order No. | Model | Capacity（kg） | Chucking Face | H | H1 | A | C | D | E | Weight（kg） | ||||||
| B | L | |||||||||||||||
| 34169-25 | GPL-100 | 100 | 63 | 92 | 71 | 122 | 164 | 110 | 32 | 43 | 3 | |||||
| 34169-30 | GPL-300 | 300 | 93 | 165 | 96 | 170 | 210 | 185 | 45 | 62 | 11 | |||||
| 34169-32 | GPL-300L | 300 | 93 | 300 | 96 | 170 | 210 | 320 | 45 | 62 | 19.5 | |||||
| 34169-35 | GPL-600 | 600 | 122 | 236 | 120 | 227 | 303 | 265 | 59 | 92 | 26 | |||||
| 34169-37 | GPL-600L | 600 | 122 | 440 | 120 | 227 | 303 | 469 | 59 | 92 | 47.5 | |||||
| 34169-40 | GPL-1000 | 1000 | 171 | 263 | 164 | 302 | 413 | 298 | 95 | 116 | 58 | |||||
| 34169-45 | GPL-2000 | 2000 | 232 | 378 | 215 | 390 | 576 | 415 | 119 | 148 | 135 | |||||
| 34169-50 | GPL-3000 | 3000 | 300 | 454 | 265 | 500 | 717 | 490 | 156 | 213 | 266 | |||||
| Model | Steel Plate | Round steel | Safety Coefficient | |||||||||||||
| Max. Lifting Capacity | Min. Thickness Required | Max. Lifting Capacity | Max. Diameter | Max. Length | ||||||||||||
| GPL-100 | 100 KG | 15 | 45 KG | 110 | 8 | x 3.5 | ||||||||||
| GPL-300 | 300 KG | 40 | 135 KG | 185 | 13 | |||||||||||
| GPL-300L | 300 KG | 40 | 135 KG | 320 | 13 | |||||||||||
| GPL-600 | 600 KG | 50 | 270 KG | 265 | 15 | |||||||||||
| GPL-600L | 600 KG | 50 | 270 KG | 469 | 15 | |||||||||||
| GPL-1000 | 1000 KG | 60 | 450 KG | 298 | 20 | |||||||||||
| GPL-2000 | 2000 KG | 70 | 870 KG | 415 | 28 | |||||||||||
| GPL-3000 | 3000 KG | 80 | 1320 KG | 490 | 32 | |||||||||||
◆ The above diagrams is only for reference. The operator should be test and chech if it is in safe range before lift away the workpiece of steel.
◆ Chart of difference in holding power by thickness:
| Thickness | Percentage of lifting capacity | |||||||
| mm | inch | GPL-3000 | GPL-2000 | GPL-1000 | GPL-600 | GPL-300 | GPL-100 | |
| T1 | UP 60 | UP 2.36” | 100% | 100% | 100% | 100% | 100% | 100% |
| T2 | UP 55 | UP 2.16" | 95% | |||||
| T3 | UP 50 | UP 1.97" | 90% | 95% | ||||
| T4 | UP 45 | UP 1.77" | 85% | 90% | ||||
| T5 | UP 40 | UP 1.57” | 75% | 85% | ||||
| T6 | UP 35 | UP 1.38" | 65% | 75% | 90% | |||
| T7 | UP 30 | UP 1.18" | 55% | 65% | 80% | |||
| T8 | UP 25 | UP 0.98“ | 45% | 55% | 70% | 90% | ||
| T9 | UP 20 | UP 0.79" | 35% | 45% | 60% | 75% | 90% | |
| T10 | UP 15 | UP 0.59” | 25% | 35% | 50% | 60% | 70% | |
| T11 | UP 10 | UP 0.39” | 15% | 25% | 35% | 45% | 50% | 70% |
| T12 | UP 5 | UP 0.20" | 10% | 15% | 20% | 25% | 30% | 40% |